User Tools

Site Tools


ccna:commandes_cisco

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
ccna:commandes_cisco [2025/05/01 22:01] – [Configuration de base] albertoccna:commandes_cisco [Unknown date] (current) – removed - external edit (Unknown date) 127.0.0.1
Line 1: Line 1:
-====== Commandes Cisco ====== 
- 
-Ci-dessous une liste des commandes dans l'IOS de cisco 
- 
-===== Commandes de visualisation ===== 
- 
-  * **show version :** afficher la version matériel et logiciel IOS. 
-  * **show flash :** affiche le contenu de la mémoire flash. 
-  * **show runnning-config :** affiche la configuration chargée en RAM (celle en cours d'exécution). 
-  * **show startup-config :** affiche la configuration stocké en mémoire flash (NVRAM : Non Volatile…). 
-  * **show interfaces status :** affiche le statut des interfaces. 
-  * **show interface fastEthernet 0/X (S0/0/X, Gig 0/0/..) :** affiche des informations sur l'interface spécifiée. 
-  * **show ip(v6) interfaces (brief) :** affiche les interfaces avec un contenu éventuellement bref. 
-  * **show interfaces trunk :** affiche les interfaces de type trunk et les VLAN transitant sur celles-ci. 
-  * **show vlan (brief) :** affiche les vlan configurés. 
-  * **show arp :** affiche la table ARP. 
-  * **show cdp neighbors :** affiche les périphériques réseaux voisins (Cisco Discovery Protocol). 
-  * **show access-list :** affiche les règles access list configurées. 
-  * **show vtp :** affiche les informations concernant Vlan Trunking Protocol. 
-  * **show spanning-tree (interface fa0/x vlan x) :** affiche les informations à propos du protocole spanning tree. 
-  * **show tech-support :** Affiche toutes les configurations présentes sur un matériel Cisco. 
- 
- 
----- 
- 
-===== Modes de commandes ===== 
- 
-  * **Switch> :** Mode utilisateur (sans droits d’administration). 
-  * **Switch> enable** ou **Switch> en :** passage en mode privilégié. 
-  * **Switch# :** mode privilégié. 
-  * **Switch# configure terminal** ou **Switch# conf t :** passage en mode configuration. 
-  * **Switch(config)# :** mode configuration. 
- 
- 
----- 
- 
-===== Configuration de base ===== 
- 
-  * **Attribuer un nom d'hôte :** 
- 
-<code> 
-Switch(config)# hostname switch1 
-</code> 
- 
-  * **Spécifier un mot de passe pour entrer en mode privilégié (en) :** 
- 
-  - stocké en clair dans la configuration : show running-config <code>Switch(config)# enable password <mot-de-passe></code> 
-  - hash visible dans la configuration : secret5 <code>Switch(config)# enable secret <mot-de-passe></code> 
- 
-  * **Mettre en place une authentification à la connexion** 
- 
-<code> 
-Switch(config)#line con 0 
-Switch(config-line)#password cisco 
-Switch(config-line)#login 
-</code> 
- 
-  * **Masquer les mots de passe de connexion dans la configuration :** 
- 
-<code> 
-Switch(config)#service password-encryption 
-</code> 
- 
-  * **Eviter la perturbation de la CLI à l’arrivé des logs :** 
- 
-<code> 
-Switch(config)#line con 0 
-Switch(config-line)#logging synchronous 
-</code> 
- 
-  * **Attribuer une adresse IPv4 à un VLAN :** 
- 
-<code> 
-Switch(config)#interface vlan 1 
-Switch(config-if)#ip address 10.10.0.1 255.255.255.0 
-Switch(config-if)#no shutdown 
-</code> 
- 
-  * **Attribuer une addresse IPv4 à une interface :** 
- 
-<code> 
-Router(config)#interface fastEthernet 0/0 
-Router(config-if)#ip address 10.10.0.254 255.255.255.0 
-Router(config-if)#no shutdown 
-</code> 
- 
-  * **Attribuer une adresse de loopback (si routeur ou commutateur de niveau 3) :** 
- 
-<code> 
-Router(config)#interface loopback 0 
-Router(config-if)#ip address 2.2.2.2 255.255.255.255 
-</code> 
- 
-  * **Spécifier une passerelle par défaut :** 
- 
-<code> 
-Switch(config)#ip default-gateway 10.10.0.254 
-</code> 
- 
-  * **Supprimer la résolution de noms DNS en cas de commandes incorrectes :** 
- 
-<code> 
-Switch(config)#no ip domain lookup 
-</code> 
- 
- 
----- 
- 
-===== Gestion de la configuration ===== 
- 
-  * **Sauvegarder la configuration dans la mémoire flash (running config → startup config) :** 
- 
-<code> 
-Switch#copy running-config startup-config 
-</code> 
-ou 
-<code> 
-Switch#wr 
-</code> 
- 
-  * **Exporter la configuration vers un fichier texte par tftp (running / startup config)** 
- 
-<code> 
-Switch#copy running-config tftp 
-Address or name of remote host []? 10.10.0.2 
-Destination filename [Switch-conf]? 
-Writing running-config....!! 
-[OK - 1120 bytes] 
-1120 bytes copied in 3.008 secs (372 bytes/sec) 
-</code> 
- 
-  * **Importer la configuration depuis un fichier texte par tftp vers run ou startup config :** 
- 
-<code> 
-Switch#copy tftp running-config 
-Address or name of remote host []? 10.10.0.2 
-Source filename []? Switch-conf 
-Destination filename [running-config]? running-config 
-Accessing tftp://10.10.0.2/Switch-conf... 
-Loading Switch-confg from 10.10.0.2: ! 
-[OK - 1120 bytes] 
-1120 bytes copied in 0.006 secs (186666 bytes/sec) 
-</code> 
- 
- 
-  * **Réinitialisation :** 
- 
-<code> 
-Switch# delete flash:/vlan.dat 
-Switch# delete flash:/config.text 
-Switch# reload 
-System configuration has been modified. Save? [yes/no]:no 
-Proceed with reload? [confirm] 
-</code> 
  
ccna/commandes_cisco.1746129710.txt.gz · Last modified: 2025/05/01 22:01 by alberto

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki