User Tools

Site Tools


ccna:commandes_cisco

This is an old revision of the document!


Commandes Cisco

Ci-dessous une liste des commandes dans l'IOS de cisco

Commandes de visualisation

  • show version : afficher la version matériel et logiciel IOS.
  • show flash : affiche le contenu de la mémoire flash.
  • show runnning-config : affiche la configuration chargée en RAM (celle en cours d'exécution).
  • show startup-config : affiche la configuration stocké en mémoire flash (NVRAM : Non Volatile…).
  • show interfaces status : affiche le statut des interfaces.
  • show interface fastEthernet 0/X (S0/0/X, Gig 0/0/..) : affiche des informations sur l'interface spécifiée.
  • show ip(v6) interfaces (brief) : affiche les interfaces avec un contenu éventuellement bref.
  • show interfaces trunk : affiche les interfaces de type trunk et les VLAN transitant sur celles-ci.
  • show vlan (brief) : affiche les vlan configurés.
  • show arp : affiche la table ARP.
  • show cdp neighbors : affiche les périphériques réseaux voisins (Cisco Discovery Protocol).
  • show access-list : affiche les règles access list configurées.
  • show vtp : affiche les informations concernant Vlan Trunking Protocol.
  • show spanning-tree (interface fa0/x vlan x) : affiche les informations à propos du protocole spanning tree.
  • show tech-support : Affiche toutes les configurations présentes sur un matériel Cisco.

Modes de commandes

  • Switch> : Mode utilisateur (sans droits d’administration).
  • Switch> enable ou Switch> en : passage en mode privilégié.
  • Switch# : mode privilégié.
  • Switch# configure terminal ou Switch# conf t : passage en mode configuration.
  • Switch(config)# : mode configuration.

Configuration de base

  • Attribuer un nom d'hôte :
Switch(config)# hostname switch1
  • Spécifier un mot de passe pour entrer en mode privilégié (en) :
  1. stocké en clair dans la configuration : show running-config
    Switch(config)# enable password <mot-de-passe>
  2. hash visible dans la configuration : secret5
    Switch(config)# enable secret <mot-de-passe>
  • Mettre en place une authentification à la connexion
Switch(config)#line con 0
Switch(config-line)#password cisco
Switch(config-line)#login
  • Masquer les mots de passe de connexion dans la configuration :
Switch(config)#service password-encryption
  • Eviter la perturbation de la CLI à l’arrivé des logs :
Switch(config)#line con 0
Switch(config-line)#logging synchronous
  • Attribuer une adresse IPv4 à un VLAN :
Switch(config)#interface vlan 1
Switch(config-if)#ip address 10.10.0.1 255.255.255.0
Switch(config-if)#no shutdown
  • Attribuer une addresse IPv4 à une interface :
Router(config)#interface fastEthernet 0/0
Router(config-if)#ip address 10.10.0.254 255.255.255.0
Router(config-if)#no shutdown
  • Attribuer une adresse de loopback (si routeur ou commutateur de niveau 3) :
Router(config)#interface loopback 0
Router(config-if)#ip address 2.2.2.2 255.255.255.255
  • Spécifier une passerelle par défaut :
Switch(config)#ip default-gateway 10.10.0.254
  • Supprimer la résolution de noms DNS en cas de commandes incorrectes :
Switch(config)#no ip domain lookup

Gestion de la configuration

  • Sauvegarder la configuration dans la mémoire flash (running config → startup config) :
Switch#copy running-config startup-config

ou

Switch#wr
  • Exporter la configuration vers un fichier texte par tftp (running / startup config)
Switch#copy running-config tftp
Address or name of remote host []? 10.10.0.2
Destination filename [Switch-conf]?
Writing running-config....!!
[OK - 1120 bytes]
1120 bytes copied in 3.008 secs (372 bytes/sec)
  • Importer la configuration depuis un fichier texte par tftp vers run ou startup config :
Switch#copy tftp running-config
Address or name of remote host []? 10.10.0.2
Source filename []? Switch-conf
Destination filename [running-config]? running-config
Accessing tftp://10.10.0.2/Switch-conf...
Loading Switch-confg from 10.10.0.2: !
[OK - 1120 bytes]
1120 bytes copied in 0.006 secs (186666 bytes/sec)
  • Réinitialisation :
Switch# delete flash:/vlan.dat
Switch# delete flash:/config.text
Switch# reload
System configuration has been modified. Save? [yes/no]:no
Proceed with reload? [confirm]
ccna/commandes_cisco.1746129710.txt.gz · Last modified: 2025/05/01 22:01 by alberto

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki